Servicing and Maintenance for Industrial and Vehicle Vacuum Pumps
Vacuum Pump Services Perth
Air & Power has provided vacuum pump services in Perth since 1990. Our qualified mobile technicians bring that industry experience to your pump, on site, across Perth and regional Western Australia. Regular maintenance keeps your vacuum equipment at optimal performance. Timely maintenance also prevents the costly downtime that a pump failure causes. A well serviced pump holds its vacuum, uses less power and costs less to keep running. This page explains what vacuum pump servicing involves, when your pump needs it and how we look after Masport pumps.

Routine servicing
What does vacuum pump servicing involve?
A service is a planned check of every part that wears. It catches small faults before they stop your line or your truck. Our service technicians cover these jobs in a typical vacuum pump service.
You receive a clear report of what we found and what is due next. Our service reports are documented, so your maintenance records stay complete. That is how regular maintenance supports operational efficiency. A vacuum system is only as reliable as its pump.

Oil, the main job
Vacuum pump maintenance for an oil-lubricated rotary vane vacuum pump
A rotary vane vacuum pump uses oil to seal, lubricate and cool the vanes. When the oil fails, the pump loses vacuum and wears fast. Oil is the first thing we check.
Oil condition tells you a lot. Discolouration, contamination or an unusual smell mean the oil needs changing. Milky or cloudy oil points to water. Dark or sludgy oil points to breakdown.
Use the oil Masport specifies: high quality non-detergent rotary compressor oil or rotary turbine oil. Don’t use transmission fluid, automotive motor oil, power steering fluid or used oil. Pumping moisture, solvent vapours or other gases breaks oil down faster. Follow the oil grade in your Masport manual.
Parts that wear
Filters, vanes and drives
An inlet filter stops dust reaching the pump. When it clogs, airflow drops and the pump works harder. In dusty sites it needs a regular check.
The exhaust filter and oil separator catch oil mist. Drain the oil separator at least daily, as exhaust blockage is a cause of overheating and lost performance. Change the exhaust filter on the schedule in your manual, or when smoke shows at the exhaust.
Vanes are the wearing part. Inspect them at least once a year. They must be replaced when they are worn to a particular height. Replace them too if they are bent, out of parallel, concave or frayed. Worn vanes stick or fail to seal, and that reduces your vacuum.
We also check the coupling, belt or hydraulic drive, because a worn drive can damage the pump.
Know the warning signs
Signs your vacuum pump needs a service
Do not wait for a breakdown. These signs mean it is time to book.
Each sign has a simple fix when it is caught early. Worn seals can develop leaks over time, so we check them at every service. Left alone, a small fault can become a full overhaul.
Service intervals
How often should a vacuum pump be serviced?
Your pump manual sets the schedule. It beats any general rule. Intervals also change with the operating conditions and how hard the pump works.
For example, Masport’s HD4 manual says to add oil about every 10 hours of operation and drain the oil separator daily. Check and clean the inlet filter and flush the pump weekly. Each year, check the mounting bolts, the coupling alignment and the vane wear.
How often the oil needs changing depends on what the pump handles, its operating hours and how contaminated the duty is. Dusty, wet or dirty duty calls for closer checks. Tell us how your pump is used and we will set a schedule that fits.

Masport pumps
How we service Masport vacuum pumps
Air & Power partners with Masport, so the Masport vacuum pump is our core work. We stock the HD3F, HD4F, HXL2F and HXL4F vacuum only pumps. We also stock the HXL2V, HXL4V and HXL75WV vacuum and pressure pumps.
Masport rotary vane pumps are also supplied in engine-drive and plug and play form. See our rotary vane pump range for the models. Engine-drive units use Honda petrol engines or diesel. Plug and play units arrive with the base, pump, drive, scrubber and separator fitted. We service all three, and we stock genuine Masport spare parts locally for a fast turnaround. Part quality decides how long a service lasts, so our team matches parts to your pump model. We service other vacuum pump brands as well.
Who uses vacuum
Industries that rely on vacuum pump services
Vacuum pumps hold, lift, move and clean. Our customers use them in food processing and packaging, manufacturing and automotive work. They also use them in construction, mining, agriculture and water treatment.
Vehicle systems are just as common. Vacuum tankers and liquid waste trucks use engine-drive or hydraulic pumps to load and empty. On a truck, a pump fault stops the job. Regular servicing keeps your vehicle earning.
Servicing, installation and repairs
Vacuum pump services Perth servicing, installation and pump repair
We cover three areas. Servicing is the routine work above. Installation gets a new pump running correctly, from fitting through to commissioning. Repairs fix a pump that has failed. We offer professional support for all three at your site or at our Belmont workshop. After the work, we test the pump. Our work is completed to Australian Standards.
This page is an overview. If you are choosing new vacuum equipment, see our vacuum systems. If your pump is already running badly, tell us the symptoms and we will advise the next step. Contact our team with your pump model and the requirements of your business.

Book a vacuum pump service
Book your vacuum pump service or call us on (08) 9424 2800. You can also email enquiries@airandpower.com.au. We are at 7 Fisher Street, Belmont WA 6104.
