Fault Finding, Rebuilds and Replacement Parts

Vacuum Pump Repairs Perth

Your vacuum pump has lost suction, started knocking or begun smoking. Air & Power has supplied and serviced vacuum systems in WA since 1990. This page covers the common faults, what a repair involves and when to rebuild instead of replace. It also explains how to book our vacuum pump repair services in Perth, so a pump failure does not stall your vacuum system.

Common faults

What are the most common vacuum pump faults?

Most faults in an oil-lubricated rotary vane pump come down to a short list. Low vacuum, noise, heat, oil leaks, oil mist, worn vanes, blocked filters and drive failure account for most call-outs.

Many start as a maintenance problem, such as dirty oil or a blocked filter. Running a pump outside its recommended conditions also causes failure. Each symptom points to a likely cause, so a technician starts with the cheapest fix first.

Low or no vacuum

Vacuum pump not pulling vacuum causes to check first

Check the system before you blame the pump. Leaks in hoses, fittings and valves are a common cause.

A blank-off test separates the two. You isolate the pump, fit a gauge at the inlet and see if it reaches its rated vacuum. If it does, the leak is in your system. If it does not, the pump needs attention.

The usual causes of impaired performance. They include worn vanes or shaft seals, a blocked inlet filter and a blocked non-return valve. Others are a collapsed hose, undersized plumbing, exhaust blockage, low pump speed and fluid in the pump.

Oil leaks, oil mist and smoke

Oil leaks, oil mist and smoke from the exhaust

Oil-lubricated pumps use oil to seal the gap between the vanes and the housing. Some mist can pass through the exhaust, which is why these pumps carry a filter.

Heavy mist or smoke is a fault. Common causes are a saturated exhaust filter, an overfilled oil reservoir or a worn shaft seal. Dark or burnt-smelling oil points to overheating or overdue oil changes. Check the oil level and colour at the sight glass each week, and change oil and filters on the schedule in your manual.

Replace the exhaust filter on schedule, not after it fails. A blocked filter raises back pressure and temperature. That shortens pump life and stresses other components.

Noise, heat and drive failure

Noise, overheating and drive or coupling failure

Clattering or knocking usually means worn, chipped or sticking vanes. A rumble or whine points to bearing wear. A knock that repeats with each turn often means a worn coupling insert or poor alignment between the pump and its motor.

The usual causes of overheating are the wrong oil or no oil, excess speed, vacuum or pressure beyond the maximum and a blocked inlet filter. Dirt on the pump, undersized plumbing and exhaust blockage also cause it. Fix the cause before restarting, and never bypass the thermal cutout.

A seized pump is a special case. Do not force it to turn. Seizure often follows running without oil or ingesting contamination, and a new pump will fail the same way if nobody finds the cause. Switch it off and call us.

How a repair works

What does a vacuum pump repair involve?

A repair usually involves the following steps:

01DiagnosisWe ask about the fault, the duty and the oil history, then inspect the pump on site.

02TestWe check performance against the pump’s rating, to separate a pump fault from a system fault.

03Strip and inspectWe measure vane wear, check bearings and seals and look at the housing.

04PartsWe quote the replacement parts you need, using genuine parts.

05RebuildWe fit the new parts, refill with the right oil and refit the pump.

06Test and reportWe test that the repaired pump is functioning properly and performing to its rating, then give you a written report.

Vane replacement is routine. Inspect the vanes at least once a year. They must be replaced when they are worn to a particular height, or if they are bent, out of parallel, concave or frayed. We can source and fit a genuine Masport rebuild kit for your pump.

Rebuild or replace

Vacuum pump rebuild or overhaul repair or replace?

A rebuild makes sense when the main castings are sound and parts are available. Replace the pump after severe internal damage, obsolete components or repeated failures.

Age and history: one fault on a well-kept pump is minor.
Cost: compare the repair quote with a new pump over its whole life, not just the day you pay.
Parts: a repair only works when parts are available. Genuine Masport parts are the safer route for a Masport pump.
Efficiency: a newer pump may use less energy, so ask us to compare running costs.

A vacuum pump overhaul can cost far less than a new pump when the castings are sound. We can give you a clear comparison before you commit.

On site or in the workshop

Vacuum pump repairs Perth on site or in our workshop

Our technicians arrive on site, diagnose the fault quickly and restore operation with minimal downtime. Our Belmont workshop services all major brands. Our mobile teams reach across Perth and regional WA.

Filter, oil and seal jobs are often done where the pump sits. A full strip and rebuild may suit the workshop. Turnaround depends on the fault and parts availability. We tell you how long the pump will be out of service before we start.

For emergency breakdowns on your vacuum pump, call us. Our mobile technicians can be dispatched 24/7 for compressor breakdowns, and we confirm out-of-hours cover for vacuum pumps when you call.

Why Air & Power

Vacuum pump repair services Perth why call Air and Power

Book a vacuum pump repair

Phone

(08) 9424 2800

Email

enquiries@airandpower.com.au

Address

7 Fisher St, Belmont, WA 6104

Secret Link