Vacuum System Supply and Installation Across WA
Vacuum Pump Installation Perth
Air & Power supplies, builds and services vacuum systems across Western Australia. Our vacuum pump installation services in Perth cover Masport rotary vane pumps, engine drive systems and plug and play systems. A pump only performs as well as the way it is installed. Location, cooling, pipework and filters decide the performance and reliability of your vacuum pumps.

Matching the pump to the job
Choosing the right vacuum system before installation
Installation starts with selection. We match the pump to your vacuum level, volume, duty cycle and site conditions. A pump that works on paper can underperform if it does not suit your operation.
Our Masport range comes in three main formats.
Oil-lubricated pumps are proven and cost effective when managed well.

Three formats compared
Engine drive vacuum system or plug and play vacuum system?
An engine drive vacuum system is self-contained and independent of mains power. That suits remote sites, mining and construction, effluent handling and vacuum tankers. The engine needs fuel, a stable footing and open air.
A plug and play vacuum system arrives with a heavy-duty mounting base and a Masport rotary vane pump. It also includes a gearbox or hydraulic drive, a scrubber and a separator. Because the parts are matched, connection to your existing setup is simpler.
Where the pump goes
Site preparation location, ventilation and cooling
Heat is the main enemy of a vacuum pump. Heat build-up is the limiting factor in pump performance, so keep the pump clean to let heat radiate away. Fan-cooled models need the fan guard clear and open space at the drive end so cooling air can escape.
Choose a spot that is level, dry and away from dust. Keep the oil sight glass easy to see and leave room for filter and oil changes.
Engine drive units add exhaust. That means placing engine units outdoors or in a well-ventilated area.
What the installation involves
Vacuum pump installation the steps from delivery to handover
A vacuum system installation follows the same order on most jobs. We confirm the scope with you first.
01Position and mount the pump on a level, stable base.
02Connect power or the engine drive.
03Fit hoses, pipework, valves and gauges.
04Install the inlet filter, exhaust filter and any tank or separator.
05Check controls, rotation and oil level.
06Leak test, then run the system under load.
07Walk you through operation and servicing at handover.
Our Belmont workshop and mobile technicians support this work across Perth and regional WA.
Pipework, filters and power
Pipework, filters, exhaust and electrical connection
Masport sets a minimum pipe inside diameter for each pump. The HD4 needs about 38 mm (1½ inches) and the HD75 needs about 64 mm (2½ inches). Plumbing smaller than this restricts airflow. We also advise keeping inlet and exhaust lines as short and direct as practical.
An inlet filter protects the pump from dust and debris. It keeps small particles out of the pump and should be checked and cleaned or replaced regularly. A blocked inlet filter is one of the causes of lost performance and overheating. Exhaust lines must not be blocked, as this is also a cause of overheating. A saturated exhaust filter raises back pressure and running temperature, so the pump works harder.
Mains-powered pumps need an electrical connection. In WA, electrical work must be done by a licensed contractor, which we take care of.

Working around the pump
Safety in vacuum pump installation guarding, exhaust and oil mist
Pumps and their hoses run hot. Masport rates hoses for air and oil temperatures up to about 149 degrees Celsius. Moving parts must be properly guarded. Guards and clear access protect your people from burns and moving parts.
Oil mist leaves through the exhaust, so a filter or oil mist separator keeps your workshop air cleaner. Exhaust filtration and oil mist separation are part of a correct setup.
Engine exhaust contains carbon monoxide, which can build up in enclosed or semi-enclosed spaces. Keep exhaust away from doors, air intakes and people.
Noise matters too. WA limits noise emissions under the Environmental Protection (Noise) Regulations 1997, and local governments handle commercial and industrial noise. Confirm your requirements with the regulator before you choose a position.
Commissioning and aftercare
After installation commissioning, servicing and spare parts
Commissioning proves the system works. It checks that the system reaches your target vacuum and holds a safe operating temperature. A good test starts with the pump isolated, so you can see what vacuum it pulls on its own. That separates a leak from a worn pump later.
Regular maintenance keeps the result. Oil changes, inlet and exhaust filter checks and gas ballast use for condensation all matter. That protects reliability and delivers real cost savings over the life of the pump. Milky oil points to water in the pump. Genuine Masport parts are stocked locally for servicing and repair, so you are not left waiting for parts.

Why Air & Power
Vacuum pump installation services Perth why call Air and Power
Air & Power has operated since 1990 and partners with Masport. We are part of The Crommelin Group and work from Belmont, with mobile technicians across Perth and regional WA.
We also supply vacuum systems for vehicle applications, including waste trucks. Tell us what you are fitting to.
Plan your vacuum pump installation
Browse our full range of Masport vacuum systems or see how a plug and play vacuum system arrives ready to connect. To plan your installation, contact Air & Power or call (08) 9424 2800.
